Router (Computer Science)

Source: Wikipedia: Router


Router

From Wikipedia, the free encyclopedia
Jump to: navigation, search
This article may be confusing or unclear to readers. Please help clarify the article; suggestions may be found on the talk page. (May 2009)
This article is about the computer networking device. For the rotating cutting tool, see Router (woodworking). For the variety of network devices found in household network setups, see residential gateway. For the software used in electronic design automation, see routing (electronic design automation).
Cisco 1800 Router
Avaya ERS 8600
Cisco 7600 Series Multilayer Switches

A router is a device that interconnects two or more computer networks, and selectively interchanges packets of data between them. Each data packet contains address information that a router can use to determine if the source and destination are on the same network, or if the data packet must be transferred from one network to another. Where multiple routers are used in a large collection of interconnected networks, the routers exchange information about target system addresses, so that each router can build up a table showing the preferred paths between any two systems on the interconnected networks.

A router is a networking device whose software and hardware are customized to the tasks of routing and forwarding information. A router has two or more network interfaces, which may be to different physical types of network (such as copper cables, fiber, or wireless) or different network standards. Each network interface is a small computer specialized to convert electric signals from one form to another.

Routers connect two or more logical subnets, which do not share a common network address. The subnets in the router do not necessarily map one-to-one to the physical interfaces of the router.[1] The term "layer 3 switching" is used often interchangeably with the term "routing". The term switching is generally used to refer to data forwarding between two network devices that share a common network address. This is also called layer 2 switching or LAN switching.

Conceptually, a router operates in two operational planes (or sub-systems):[2]

* Control plane: where a router builds a table (called routing table) as how a packet should be forwarded through which interface, by using either statically configured statements (called statical routes) or by exchanging information with other routers in the network through a dynamical routing protocol;
* Forwarding plane: where the router actually forwards traffic (called packets in IP) from ingress (incoming) interfaces to an egress (outgoing) interface that is appropriate for the destination address that the packet carries with it, by following rules derived from the routing table that has been built in the control plane.

Contents
[hide]

* 1 Forwarding plane (a.k.a. data plane)
* 2 Types of routers
o 2.1 Routers for Internet connectivity and internal use
* 3 History
o 3.1 Enterprise routers
+ 3.1.1 Access
+ 3.1.2 Distribution
+ 3.1.3 Core
* 4 Router Manufacturers
* 5 References
* 6 External links

[edit] Forwarding plane (a.k.a. data plane)
Main article: Forwarding plane

For pure Internet Protocol (IP) forwarding function, a router is designed to minimize the state information on individual packets. A router does not look into the actual data contents that the packet carries, but only at the layer 3 addresses to make a forwarding decision, plus optionally other information in the header for hint on, for example, QoS. Once a packet is forwarded, the router does not retain any historical information about the packet, but the forwarding action can be collected into the statistical data, if so configured.

Forwarding decisions can involve decisions at layers other than the IP internetwork layer or OSI layer 3. A function that forwards based on data link layer, or OSI layer 2, information, is properly called a bridge or switch. This function is referred to as layer 2 switching, as the addresses it uses to forward the traffic are layer 2 addresses in the OSI layer model.

Besides making decision as which interface a packet is forwarded to, which is handled primarily via the routing table, a router also has to manage congestion, when packets arrive at a rate higher than the router can process. Three policies commonly used in the Internet are tail drop, random early detection, and weighted random early detection. Tail drop is the simplest and most easily implemented; the router simply drops packets once the length of the queue exceeds the size of the buffers in the router. Random early detection (RED) probabilistically drops datagrams early when the queue is about to exceed a pre-configured size of the queue. Weighted random early detection requires a weight on the average queue size to act upon when the traffic is about to exceed the pre-configured size, so that short bursts will not trigger random drops.

Another function a router performs is to decide which packet should be processed first when multiple queues exist. This is managed through QoS (Quality of Service), which is critical when VoIP (Voice over IP) is deployed, so that delays between packets do not exceed 150ms to maintain the quality of voice conversations.

Yet another function a router performs is called "policy based routing" where special rules are constructed to override the rules derived from the routing table when packet forwarding decision is made.

These functions may or may not be performed through the same internal paths that the packets travel inside the router. Some of the functions may be performed through an ASIC (application-specific integrated circuit) to avoid overhead caused by multiple CPU cycles, and others may have to be performed through the CPU as these packets need special attention that cannot be handled by an ASIC.
[edit] Types of routers
A demonstration of a router forwarding information to many clients.

Routers may provide connectivity inside enterprises, between enterprises and the Internet, and inside internet service providers (ISPs). The largest routers (for example the Cisco CRS-1 or Juniper T1600) interconnect ISPs, are used inside ISPs, or may be used in very large enterprise networks. The smallest routers provide connectivity for small and home offices.
[edit] Routers for Internet connectivity and internal use

Routers intended for ISP and major enterprise connectivity almost invariably exchange routing information using the Border Gateway Protocol (BGP). RFC 4098[3] defines several types of BGP-speaking routers according to the routers' functions:

* Edge Router: An ER is placed at the edge of an ISP network. The router speaks external BGP (EBGP) to a BGP speaker in another provider or large enterprise Autonomous System(AS). This type of routers is also called PE (Provider Edge) routers.
* Subscriber Edge Router: An SER is located at the edge of the subscriber's network, it speaks EBGP to its provider's AS(s). It belongs to an end user (enterprise) organization. This type of routers is also called CE (Customer Edge) routers.
* Inter-provider Border Router: Interconnecting ISPs, this is a BGP speaking router that maintains BGP sessions with other BGP speaking routers in other providers' ASes.
* Core router: A Core router is one that resides within an AS as back bone to carry traffic between edge routers.

Within an ISP: Internal to the provider's AS, such a router speaks internal BGP (IBGP) to that provider's edge routers, other intra-provider core routers, or the provider's inter-provider border routers.
"Internet backbone:" The Internet does not have a clearly identifiable backbone, as did its predecessors. See default-free zone (DFZ). Nevertheless, it is the major ISPs' routers that make up what many would consider the core. These ISPs operate all four types of the BGP-speaking routers described here. In ISP usage, a "core" router is internal to an ISP, and used to interconnect its edge and border routers. Core routers may also have specialized functions in virtual private networks based on a combination of BGP and Multi-Protocol Label Switching (MPLS).[4]

Routers are also used for port forwarding for private servers.
[edit] History
Leonard Kleinrock and the first IMP.
A Cisco ASM/2-32EM router deployed at CERN in 1987.

The very first device that had fundamentally the same functionality as a router does today, i.e a packet switch, was the Interface Message Processor (IMP); IMPs were the devices that made up the ARPANET, the first packet switching network. The idea for a router (although they were called "gateways" at the time) initially came about through an international group of computer networking researchers called the International Network Working Group (INWG). Set up in 1972 as an informal group to consider the technical issues involved in connecting different networks, later that year it became a subcommittee of the International Federation for Information Processing. [5]

These devices were different from most previous packet switches in two ways. First, they connected dissimilar kinds of networks, such as serial lines and local area networks. Second, they were connectionless devices, which had no role in assuring that traffic was delivered reliably, leaving that entirely to the hosts (although this particular idea had been previously pioneered in the CYCLADES network).

The idea was explored in more detail, with the intention to produce a real prototype system, as part of two contemporaneous programs. One was the initial DARPA-initiated program, which created the TCP/IP architecture of today. [6] The other was a program at Xerox PARC to explore new networking technologies, which produced the PARC Universal Packet system, although due to corporate intellectual property concerns it received little attention outside Xerox until years later. [7]

The earliest Xerox routers came into operation sometime after early 1974. The first true IP router was developed by Virginia Strazisar at BBN, as part of that DARPA-initiated effort, during 1975-1976. By the end of 1976, three PDP-11-based routers were in service in the experimental prototype Internet. [8]

The first multiprotocol routers were independently created by staff researchers at MIT and Stanford in 1981; the Stanford router was done by William Yeager, and the MIT one by Noel Chiappa; both were also based on PDP-11s. [9] [10] [11] [12]

As virtually all networking now uses IP at the network layer, multiprotocol routers are largely obsolete, although they were important in the early stages of the growth of computer networking, when several protocols other than TCP/IP were in widespread use. Routers that handle both IPv4 and IPv6 arguably are multiprotocol, but in a far less variable sense than a router that processed AppleTalk, DECnet, IP, and Xerox protocols.

In the original era of routing (from the mid-1970s through the 1980s), general-purpose mini-computers served as routers. Although general-purpose computers can perform routing, modern high-speed routers are highly specialized computers, generally with extra hardware added to accelerate both common routing functions such as packet forwarding and specialised functions such as IPsec encryption.

Still, there is substantial use of Linux and Unix machines, running open source routing code, for routing research and selected other applications. While Cisco's operating system was independently designed, other major router operating systems, such as those from Juniper Networks and Extreme Networks, are extensively modified but still have Unix ancestry.
[edit] Enterprise routers

All sizes of routers may be found inside enterprises. The most powerful routers tend to be found in ISPs and academic & research facilities. Large businesses may also need powerful routers.

A three-layer model is in common use, not all of which need be present in smaller networks.[13]
[edit] Access

Access routers, including SOHO, are located at customer sites such as branch offices that do not need hierarchical routing of their own. Typically, they are optimized for low cost.
[edit] Distribution

Distribution routers aggregate traffic from multiple access routers, either at the same site, or to collect the data streams from multiple sites to a major enterprise location. Distribution routers often are responsible for enforcing quality of service across a WAN, so they may have considerable memory, multiple WAN interfaces, and substantial processing intelligence.

They may also provide connectivity to groups of servers or to external networks. In the latter application, the router's functionality must be carefully considered as part of the overall security architecture. Separate from the router may be a firewall or VPN concentrator, or the router may include these and other security functions.

When an enterprise is primarily on one campus, there may not be a distinct distribution tier, other than perhaps off-campus access. In such cases, the access routers, connected to LANs, interconnect via core routers.
[edit] Core

In enterprises, a core router may provide a "collapsed backbone" interconnecting the distribution tier routers from multiple buildings of a campus, or large enterprise locations. They tend to be optimized for high bandwidth.

When an enterprise is widely distributed with no central location(s), the function of core routing may be subsumed by the WAN service to which the enterprise subscribes, and the distribution routers become the highest tier.
[edit] Router Manufacturers

The major router manufacturers include:

* Cisco Systems
* D-link
* Juniper Networks
* Avaya
* Brocade
* Alcatel-Lucent
* Fujitsu
* Huawei
* ZTE
* Extreme Networks
* UTStarcom
* Netgear
* ZyXEL

[edit] References

1. ^ Requirements for IPv4 Routers,RFC 1812, F. Baker, June 1995
2. ^ Requirements for Separation of IP Control and Forwarding,RFC 3654, H. Khosravi & T. Anderson, November 2003
3. ^ Terminology for Benchmarking BGP Device Convergence in the Control Plane,RFC 4098, H. Berkowitz et al.,June 2005
4. ^ BGP/MPLS VPNs,RFC 2547, E. Rosen and Y. Rekhter, April 2004
5. ^ Davies, Shanks, Heart, Barker, Despres, Detwiler, and Riml, "Report of Subgroup 1 on Communication System", INWG Note #1.
6. ^ Vinton Cerf, Robert Kahn, "A Protocol for Packet Network Intercommunication", IEEE Transactions on Communications, Volume 22, Issue 5, May 1974, pp. 637 - 648.
7. ^ David Boggs, John Shoch, Edward Taft, Robert Metcalfe, "Pup: An Internetwork Architecture", IEEE Transactions on Communications, Volume 28, Issue 4, April 1980, pp. 612- 624.
8. ^ Craig Partridge, S. Blumenthal, "Data networking at BBN"; IEEE Annals of the History of Computing, Volume 28, Issue 1; January-March 2006.
9. ^ Valley of the Nerds: Who Really Invented the Multiprotocol Router, and Why Should We Care?, Public Broadcasting Service, Accessed August 11, 2007.
10. ^ Router Man, NetworkWorld, Accessed June 22, 2007.
11. ^ David D. Clark, "M.I.T. Campus Network Implementation", CCNG-2, Campus Computer Network Group, M.I.T., Cambridge, 1982; pp. 26.
12. ^ Pete Carey, "A Start-Up's True Tale: Often-told story of Cisco's launch leaves out the drama, intrigue", San Jose Mercury News, December 1, 2001.
13. ^ Oppenheimer, Pr (2004). Top-Down Network Design. Indianapolis: Cisco Press. ISBN 1587051524.

[edit] External links
Search Wikimedia Commons Wikimedia Commons has media related to: Network routers
Search Wikibooks Wikibooks has a book on the topic of
Computer Networks/Routing
Search Wiktionary Look up router in Wiktionary, the free dictionary.

* Internet Engineering Task Force, the Routing Area
* Internet Corporation for Assigned Names and Numbers
* North American Network Operators Group
* Réseaux IP Européens (European IP Networks)
* American Registry for Internet Numbers
* Asia-Pacific Network Information Center
* Latin American Network Information Center
* African Region Internet Registry
* Wireless Network Switching Subsystem
* Network router cheat sheet

Retrieved from "http://en.wikipedia.org/wiki/Router"
Categories: Internet architecture | Routers | Hardware routers | Networking hardware | Server appliance
Hidden categories: Wikipedia articles needing clarification from May 2009 | All Wikipedia articles needing clarification
Personal tools

* New features
* Log in / create account

Namespaces

* Article
* Discussion

Variants

Views

* Read
* Edit
* View history

Actions

Search
Search
Navigation

* Main page
* Contents
* Featured content
* Current events
* Random article

Interaction

* About Wikipedia
* Community portal
* Recent changes
* Contact Wikipedia
* Donate to Wikipedia
* Help

Toolbox

* What links here
* Related changes
* Upload file
* Special pages
* Permanent link
* Cite this page

Print/export

* Create a book
* Download as PDF
* Printable version

Languages

* العربية
* বাংলা
* Bân-lâm-gú
* Bosanski
* Brezhoneg
* Български
* Català
* Česky
* Dansk
* Deutsch
* Eesti
* Ελληνικά
* Español
* Esperanto
* Euskara
* فارسی
* Français
* Gaeilge
* Galego
* 한국어
* हिन्दी
* Hrvatski
* Bahasa Indonesia
* Italiano
* עברית
* ລາວ
* Latviešu
* Lëtzebuergesch
* Lietuvių
* Lumbaart
* Magyar
* മലയാളം
* Bahasa Melayu
* Nederlands
* 日本語
* ‪Norsk (bokmål)‬
* ‪Norsk (nynorsk)‬
* Occitan
* Piemontèis
* Polski
* Português
* Română
* Русский
* Simple English
* Slovenčina
* Slovenščina
* Српски / Srpski
* Suomi
* Svenska
* தமிழ்
* ไทย
* Türkçe
* Українська
* اردو
* Tiếng Việt
* 吴语
* ייִדיש
* 中文

* This page was last modified on 15 June 2010 at 13:01.
* Text is available under the Creative Commons Attribution-ShareAlike License; additional terms may apply. See Terms of Use for details.
Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a non-profit organization.
* Contact us

* Privacy policy
* About Wikipedia
* Disclaimer

Unless otherwise stated, the content of this page is licensed under Creative Commons Attribution-ShareAlike 3.0 License